Cooling System Air Purging Tool, Part# 031956, $44.95 

 

Low coolant levels can cause severe overheating, resulting in engine damage. Especially designed for the MGB 1977-1980 without a radiator cap. Solid Brass fittings with high pressure hose to prevent kinking. Also fits: TR-7 1975-1980, MG Midget 1500cc, MG Midget 1275cc

31956.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com

Original Duplicates Tool Line

Carburetor Spacer Kit HS2 HS4,

Part# 031940, $45.95 

Fits HS-2 & HS-4 SU Carbs.  The spacer raises the fuel level in the float bowel and the jet assembly.  This allows for availability of fuel closer to the top of the jet assembly at the upper end of the rev band especially in 2nd and 3rd gear. Proven in racing. Instructions Included.

031940-500.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com

Overdrive Drain Plug Spanner,

Part# 031955, $41.95 

In order to service the transmission fitted with the A-Type overdrive, it is necessary to remove the large brass or steel drain plug. It is often very difficult to remove since it seizes in the aluminum case. This tool is designed to engage on the six notches and provides proper leverage for safe removal and replacement.
Fits Austin Healey 3000 BN2-BJ8, Triumph TR-3B-4A & TR-250-6
 

31955.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com

Rear Axle Hub Nut Wrench, 

Part# 031953, $45.95 

Designed to fit either the original style hub nut or the later style currently being supplied by most British Car parts suppliers. Made from 3/8" thick solid steel. Fits Bugeye, Sprite & Midget. Use with any 1/2 drive ratchet wrench. Instructions included.

031953-500.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com

Steering Wheel Puller, 

Part# 031941, $45.95 

The factory never provided a means to remove the steering wheel on 1977-1980 MGB's. The all rubber steering wheel on these models must be removed in order to change the turn signal assembly or to upgrade to a performance wheel. Instructions included.

031941-500.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com

Grease Cup Puller,

Part# 031943, $39.95

 

Pulling the front grease cups can be very frustrating when servicing the many WIRE WHEEL models.  Grease cups must be removed to pack wheel bearings, replacing front seals, rotors or performing front end rebuilds.  Shop quality service tool. Instructions included.

031943-500.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com

Rear Axle Puller, Tube Type

 Part# 031944, $34.95

Used for MGB & MGBGT's rear axle service work. Axles must be removed in order to change wheel bearings, 3rd member front pinion bearing or thrust washers to eliminate that clunk-clunk sound. Instructions included.

031944-225.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com

Window Seal Clip Tool,

 Part# 031948, $34.95 

Triumph, Sprite & Midget door glass outer rubber seal and inner fuzzy seals utilize clips to hold them in place.  This can be a very frustrating job.  During routine replacement or during restoration this handy tool magnetically holds the clip in place on the tool to facilitate installation. Shop quality tool.  Instructions included.

031948-225.jpg

To order Click here to Contact us or send an email to britstuph@gmail.com